The E7S Slim Configured package provides an E7 drive in a NEMA 1 enclosure, with space for several commonly used options, such as reactors, input filters, circuit breakers, etc. The E7 and E7S Slim Configured have been designed for flexibility in providing the features and options commonly specified by facility designers.

The E7 Drive is a variable torque AC drive, designed specifically for HVAC applications in building automation. A new benchmark for size, cost, performance, benefits, and quality, the E7 includes numerous built-in features such as network communications, H/O/A, PI control, and energy-savings functions.

The E7 has embedded communications for the popular building automation protocols, Johnson Controls Metasys® N2 and Siemens APOGEE™ FLN, as well as Modbus. An optional LonWorks®, EtherNet/IP, or BACnet interface cards are also available.

E7 Performance Features VT Ratings:  1-40 HP, 208 VAC 1-100 HP, 480 VAC Overload capacity: 110% for 60 sec (150% peak) Starting torque: 100% at 3 Hz DC injection braking: at start or stop, adjustable, current limited (anti-windmilling) Motor preheat function Adjustable accel/decel: 0.1 to 6000 sec. Controlled speed range: 40:1 Critical frequency rejection: 3 selectable, adjustable bands Torque limiting: 30-180% Energy $aving control Torque boost: full range, auto Power loss ride-thru: 2 sec Inertia ride-thru Auto restart after power loss or resettable fault, selectable, programmable Feedback signal loss detection Serial communications loss detection "Up/Down" floating point control capability Stationary motor auto-tuning Customizable monitor display Sleep function Run permissive input Ramp-to-stop or coast-to-stop selection Runtime changes in control and display Project-specific parameter reinitialization E7 Protective Features Current limited stall prevention Heat sink over-temperature, speed fold-back Cooling fan operating hours recorded Bi-directional start into rotating motor at synchronized speed DC bus charge indicator Current limiting DC bus fuse Optically-Isolated controls Short circuit protection: Phase-phase and phase-neutral Ground fault protection Electronic motor overload: UL Current and torque limit Fault display: last 10 faults Fault circuit: OC, OV, OT Over torque and under torque protection Program security code "Hunting" prevention logic Reverse prohibit selectability

E7 Design Features 32-bit microprocessor logic Flash upgradeable firmware Non-volatile memory, program retention Surface-mount devices Displacement power factor: 0.98 Output frequency: 0.1 to 120 Hz Frequency resolution: 0.06 Hz Frequency regulation: 0.1% Control Terminal Board: Quick disconnect, removable Carrier frequency: selectable to 15 kHz 3%DC bus reactor: 30-40 HP, 208 VAC; 40-100 HP, 480 VAC; optional on lower ratings Keypad Operator: Hand/Off/Auto, built-in copy feature, 7 languages LCD display: 5 lines, 16 characters each 24 VDC control logic Transmitter/Option power supply Output contacts: One form C and two programmable form A Input/output terminal status Input terminals: 5 programmable multifunction input terminals Fault input: Programmable Diagnostic fault indication in selected language Timer function: Elapsed time, Delay on start, Delay on stop RS-422/485 port: Embedded Metasys N2, APOGEE FLN, and Modbus Volts/hertz ratio: Preset and programmable V/Hz patterns Multi-speed settings: 5 available Remote speed command: 0-10 VDC or 4-20 mA, direct or reverse-acting Setpoint (PI) control with inverse or square root input, differential control via two feedback capability Feedback signal: low pass filter Speed command: bias and gain Analog outputs: Programmable, two, 0-10 VDC Meter Functions: Volt, amp, kilowatt, elapsed run time, speed command Output Current Transformers, qty 3 NEMA 1 UL, cUL listed; CE marked; IEC 146 MTBF: exceeds 28 years Input line disconnect switch E7S Slim Configured Options 65 kA Circuit Breaker Disconnect (Package SCCR = 65 kA) 100 kA Circuit Breaker Disconnect (Package SCCR = 100 kA) Input filter DC bus reactor Engraved nameplates Speed potentiometer Pressure/electrical transducer, 3-15 PSI Analog outputs: 2 programmable, 4-20 mA Communication Interface: LonWorks, BACnet, Ethernet/IP DriveWizard™ upload/download and monitoring/graphing software

E7S Slim Configured Drives - 1-40HP, 208V and 1-100HP 480V, NEMA 1

208V | 480V

Rated InputVoltage	Configured Drive Model Number	Rated Output Current (Amps)	Nominal HP1
208V	E7SVD004	4.6	1
	E7SVD007	7.5	2
	E7SVD010	10.6	3
208V	E7SVD016	16.7	5
	E7SVD024	24.2	7.5
	E7SVD030	30.8	10
208V	E7SVD046	46.2	15
	E7SVD059	59.4	20
	E7SVD074	74.8	25
208V	E7SVD088	88	30
	E7SVD114	114	40

1. Horsepower rating is based on standard NEMA B 4-pole motor design and NEC table 430.150 Full-Load Current, Three-Phase Alternating Current

Rated InputVoltage	Configured Drive Model Number NEMA 1	Rated Output Current (Amps)	Nominal HP1
480V	E7SVB002	2.1	1
	E7SVB003	3.4	2
	E7SVB004	4.8	3
480V	E7SVB007	7.6	5
	E7SVB011	11	7.5
	E7SVB014	14	10
480V	E7SVB021	21	15
	E7SVB027	27	20
	E7SVB034	34	25
480V	E7SVB040	40	30
	E7SVB052	52	40
	E7SVB065	65	50
480V	E7SVB077	77	60
	E7SVB096	96	75
	E7SVB124	124	100

1. Horsepower rating is based on standard NEMA B 4-pole motor design and NEC table 430. 150 Full-Load Current, Three-Phase Alternating Current, Three Phase Alternating Current Motors